T51 Top Hammer Drill Bit Bench Drilling Bit 115mm/127mm Thread Button Bit for Quarry and Mining

• Customization: Available
• Customized: Customized
• Standard: ISO
• Model NO.: 127mm-T51
• Length: Stub-length
• Type: Center Drill Bit
• Material: Tungsten Carbide
• Usage: Well Drilling
• Transport Package: Wooden Box
• Specification: 127mm-T51
• Trademark: YIKUANG
• Origin: China
• HS Code: 8207191000
• Production Capacity: 10000

Product Description

top hammer drill bit BENCH DRILLING BIT t38/t45/t51/t60-64mm/76mm/89mm/102mm/115mm/127mm thread button bit for quarry and mining

    The drill bit is the main tool of mining engineering impact drill, drilling and drilling machine parts is matched with the company, the product adopts the high quality alloy bit Zhuzhou hard alloy factory, the carcass quality 40Cr, 42CrMo and other materials Seiko production, to ensure the strength and toughness of drill bit. The company launched the conical connection hard alloy drill bit are straight and cross, three blade, ball gear and other four kinds of forms, many varieties and specifications
     According to the drilling machine model, rock properties, hardness, toughness, pressure (pressure) choose a bit hard alloy bit type and, in general, fissures of rock should choose a bit; cross bit, three edge type bit is widely applicable to all kinds of rock, especially in hard and super hard abrasive high the fissures in the more obvious advantages; button bits for except the high rock abrasiveness of rock.
The usage method and matters needing attention of buttton bit
    1. Ensure a good match with the tapered drill rod (taper is consistent, the depth of the drill rod inserted into the drill hole must be more than 25mm, and the head of the drill rod should not be filled with the bottom of the drill hole, otherwise it is easy to cause the loss of the drill bit; Note: it is best to use the drill bit with the same tapered drill rod manufacturer to ensure that its taper is consistent and well coordinated.
2. the drilling machine should lower the air volume and reduce the damage to the bit caused by high stress on the cemented carbide sheet, and then use the normal air rate when the drill bit is fully drilled into the rock;
3. When the width of the platform is more than 3mm, it should be replaced or milled in time to avoid reducing the drilling speed, causing bit fragments, splits and reducing service life; When the taper of the bit appears, it is necessary to replace or repair the bit in time, otherwise, the bit will be worn seriously, the drilling speed will be reduced, and even the drill bit will be stuck. Use 46-60 silicon carbide grinding wheel when grinding, its line speed is not less than 18 m / s.
4. When using brazing bit, if it encounters foreign body such as steel bar, the drilling position should be adjusted to prevent the bit from being destroyed;
5. When rock drilling is easy to appear, one character bit should be replaced by cross bit or ball bit.
6. for the rock which causes serious wear of drill bit, slow drilling and serious debris, consideration should be given to replacing other alloy grade bit or using cross type bit and ball bit, and notify us in writing in time. In order to deal with in time.

diameter		Alloy number * diameter			Flushing hole		Thread form	Weight (kg)
mm	inch	front	gauage	angle	front	sid
41	1 5/8	2*9	4*9	35°	1	1	R32	0.6
41	1 5/8	2*8	5*9	35°	1	1	R32	0.7
43	1 11/16	2*9	5*9	35°	1	2	R32	0.7
43	1 11/16	2*9	5*10	35°	1	1	R32	0.7
43	1 11/16	2*9	6*9	40°	2	-	R32	0.7
45	1 3/4	2*9	5*11	30°	1	1	R32	0.8
45	1 3/4	2*9	6*10	35°	2	-	R32	0.8
45	1 3/4	3*8	6*10	30°	3	-	R32	0.8
48	1 7/8	2*9	5*11	35°	1	1	R32	0.9
48	1 7/8	2*9	6*10	40°	2	-	R32	0.9
48	1 7/8	3*8	6*10	40°	3	-	R32	0.9
48	1 7/8	3*9	6*10	30°	3	-	R32	0.9
51	2	2*10	5*11	35°	1	1	R32	1.0
51	2	2*10	6*10	40°	2	-	R32	1.0
51	2	3*9	6*10	35°	3	-	R32	1.0
57	2 1/4	3*9	6*11	35°	3	-	R32	1.3
64	2 1/2	3*10,1*10	6*11	35°	3	-	R32	1.6
64	2 1/2	4*10	8*10	40°	2	-	R32	1.6
76	3	4*11	8*11	40°	2	-	R32	2.6
64	2 1/2	3*11	6*12	35°	3	-	T38
64	2 1/2	4*10	8*10	40°	2	-	T38
64	2 1/2	3*10,1*10	6*11	35°	3	-	T38
70	2 3/4	4*11	8*11	40°	2	-	T38
70	2 3/4	4*10,1*10	8*11	30°	4	-	T38
70	2 3/4	3*10,1*10	6*12	35°	3	-	T38
76	3	4*11	8*11	40°	2	-	T38
76	3	5*11	8*13	35°	2	1	T38
76	3	3*11,1*11	6*12	35°	3	1	T38
76	3	4*11,1*11	8*12	35°	4	-	T38
76	3	4*11,1*11	8*11	40°	4	-	T38
89	3 1/2	4*13	8*13	40°	2	-	T38
89	3 1/2	5*13	8*13	35°	2	-	T38
89	3 1/2	6*11	8*12	35°	2	-	T38
89	3 1/2	3*11,2*11	6*13	35°	3	1	T38
89	3 1/2	4*11,1*11	8*13	35°	4		T38
89	3 1/2	4*13,1*13	8*13	35°	4		T38

 

FAQ:

Q: Are you a manufacturer or trading company?

A: We are a specialized manufacturer.

 

Q: What are your main products, and used for?

A: Our products include core barrel, casing, drill rod, drill rig and other drilling parts.They are used for mineral exploration, geological drilling,

 

Q: How about the delivery terms?

A: 1.Payment: T/T, L/C, Western Union, Paypal, 30% deposit in advance and rest before delivery

2. Min. order quantity: 1 piece.

3. Transportation: By sea, train.

 

Q: How about discount?

A: Price is based on products and order quantity.

 

Q: Do you accept sample order?

A: Yes sure, please contact us for details.

 

Q: How about your after-sales service?

A: As a manufacturer has 32 years of history we offer prompt technology support for all problems and questions. Besides, we accept goods return or replace for quality problem.

 

Q: Where is your factory located in?

A: Our factory is located in Linqing city, Shandong province, China.

 

Q: How does your company control the quality?

A: Quality first. In order to guarantee high quality for our products, our always make a serious inspection for all products and raw materials in strict procedure.

We have obtained certificate of ISO9001*Yikuang is professional production of drilling tools, if you want to know more about our products, please feel free to contact us.

Pls feel freely to contact us !!!

Address:Xintai Industrial Park ,Linqing City,Shandong Pro.China.